This seems to use similar methodology as above, where you would be able to use your existing home wiring (in this case electrical) to essentially create a hardwired connection between the Gateway/modem/router combo and the WAP. Thus essentially this should work as a hardwired Ethernet port without actually needing to install Ethernet cabling throughout the house. My understanding is that I would use a Ethernet cable from the Uverse Gateway/modem/router combo, plug it into a MOCA Ethernet-to-Coaxial Adapter (which plugs into the Coax jack near the Gateway/modem/router combo), the signal should be transmitted over the Coax cable already installed in my house to another Coax jack in the house, which I would then plug another MOCA Ethernet-to-Coaxial Adapter into, then plug the Wireless Access Point into it. Ethernet-to-Coaxial Adapters would plug into the Uverse Gateway/modem/router combo on one end and the WAP on the other end. Dish or other satellite TV, AT&T Internet, and AT&T U-verse coax networks. This method seems it would instead use your existing Coax cabling to send signal then convert back to Ethernet connections on both ends. Then use a inexpensive router as a AP connected to the moca via ethernet to. Does anyone know of a system this would work with? However I have not seen anyone having success in doing this. This option would seem to use the wireless signal between the two mesh system interfaces. Option 1) Could I install a mesh WiFi network (such as orbi or eero) then move the WAP from being connected to the Uverse provided Gateway/router/modem combo box and instead plug the WAP into the satellite/beacon of the mesh system in a different part of the house (closer to the wireless TV receivers)? Yet wont work with AT&T internet, satellite, and AT&T. (before I go throwing money at the issue to experiment what works and what doesn't) It transmits over the same coax cables as your fiber-optic or cable TV service without any interference. Hoping that somebody can comment on if any of the below alternatives would work. I suspect there are because I have seen at least a few small comments about different technologies, but no solid answers or reasoning. More than 1 TV just get a moca approved splitter. Most people have more coax running through their walls. My question is: Are there any other options? You can connect your boxes via Ethernet direct to their ont or via coax (using moca). So far, the only solutions I have seen are:ġ) move WAP closer to the receiver by running longer Ethernet cord from itģ) move equipment out into the open/make sure there are no obstructions or interference near equipmentĤ) swap to hard wired box instead of wirelessįor me, these are not options, I won't get into the 'whys' of each because it's not relevant. I have been on a few different threads about Uverse wireless receivers having poor reception because they are too far away from the WAP. Call or go to att.com/internet to see if you qualify.Issue: Wireless TV receiver is getting poor signal from the wireless access point (WAP) *Available in limited markets and may not be available in your area. Restrictions apply.ĭIRECTV via Internet and AT&T Fiber each sold and billed separately. Additional taxes, fees and charges may apply. And you will have your Ethernet for the TV, providing that your U-verse router is MoCA enabled. This option lets you: Transfer shows to/from other DVRs. In a series recording, max 30 episodes stored (oldest deleted first which may be in less than 90 days). Option 1: Wireless Option 2: Ethernet Option 3: MoCA Option 1: Wireless Use this option if you have a TiVo BOLT /BOLT+ or TiVo Roamio Plus/Pro and want to stream shows to your mobile device (not to other TiVo boxes). Restrictions apply.ĪT&T recommends a minimum internet speed of 8Mbps per stream for optimal viewing. Req’s you to select offer.ĭIRECTV STREAM not available to DIRECTV and U-verse TV customers. Services auto-renew after 3 months at then prevailing rate (currently $28/mo.) unless you change or cancel. May require compatible smart home device, app and service. Requires separate subscription / sign-in for Netflix and Pandora. 1 Whole-home Wi-Fi connectivity may require AT&T Smart Wi-Fi Extender(s), sold separately.ĭata connection required.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |